Aruba IAP-335 (RW) Instant
(JW823A)
WI-FI RADIO SPECIFICATIONS
• AP type: Indoor, dual radio, 5 GHz 802.11ac 4x4 MIMO and 2.4 GHz 802.11n 4x4 MIMO
- In addition to 802.11n, the 2.4 GHz radio supports all 802.11ac features as well (proprietary extension)
• Software-configurable dual radio supports 5 GHz (Radio 0) and 2.4 GHz (Radio 1)
• 5 GHz:
- Four spatial stream Single User (SU) MIMO for up to 1,733 Mbps wireless data rate to individual 4x4 VHT80 or 2x2 VHT160 client devices
- Four spatial stream Multi User (MU) MIMO for up to 1,733 Mbps wireless data rate to up to three MU-MIMO capable client devices simultaneously
• 2.4 GHz: Four spatial stream Single User (SU) MIMO for up to 800 Mbps wireless data rate to individual 4x4 VHT40 client devices (600 Mbps for HT40 802.11n client devices)
• Support for up to 255 associated client devices per radio, and up to 16 BSSIDs per radio
• Supported frequency bands (country-specific restrictions apply):
- 2.400 to 2.4835 GHz
- 5.150 to 5.250 GHz
- 5.250 to 5.350 GHz
- 5.470 to 5.725 GHz
- 5.725 to 5.850 GHz
• Available channels: Dependent on configured regulatory domain
• Dynamic frequency selection (DFS) optimizes the use of available RF spectrum
• Supported radio technologies:
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
• Supported modulation types:
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
• Transmit power: Configurable in increments of 0.5 dBm
• Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):
- 2.4 GHz band: +24 dBm (18 dBm per chain)
- 5 GHz band: +24 dBm (18 dBm per chain)
- Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain
• Advanced Cellular Coexistence (ACC) minimizes interference from cellular networks
• Maximum ratio combining (MRC) for improved receiver performance
• Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
• Short guard interval for 20 MHz, 40 MHz, 80 MHz and 160 MHz channels
• Space-time block coding (STBC) for increased range and improved reception
• Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
• Transmit beam-forming (TxBF) for increased signal reliability and range
• Supported data rates (Mbps):
- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 600 (MCS0 to MCS31)
- 802.11ac: 6.5 to 1,733 (MCS0 to MCS9, NSS = 1 to 4 for VHT20/40/80, NSS = 1 to 2 for VHT160)
• 802.11n high-throughput (HT) support: HT 20/40
• 802.11ac very high throughput (VHT) support: VHT 20/40/80/160
• 802.11n/ac packet aggregation: A-MPDU, A-MSDU
WI-FI ANTENNAS
• AP-334/IAP-334: Four RP-SMA connectors for external dual band antennas. Internal loss between radio interface and external antenna connectors (due to diplexing circuitry): 2.3 dB in 2.4 GHz and 1.2 dB in 5 GHz.
• AP-335/IAP-335
- Four (vertically polarized) integrated 2.4 GHz downtilt omni-directional antennas for 4x4 MIMO with peak antenna gain of 4.3 dBi per antenna.
- Each 5 GHz radio chain has both a vertically and a horizontally polarized antenna element; AP software automatically and dynamically selects the best set of elements for each data packet transmitted or received.
- Four integrated vertically polarized 5 GHz downtilt omnidirectional antennas for 4x4 MIMO with peak antenna gain of 5.4 dBi per antenna
- Four integrated horizontally polarized 5 GHz downtilt omni-directional antennas for 4x4 MIMO with peak antenna gain of 4.2 dBi per antenna
- Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 degrees.
- Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the effective per-antenna pattern is 2.6dBi in 2.4 GHz and 2.5 dBi (vertical) or 2.1 dB (horizontal) in 5 GHz.
OTHER INTERFACES
• One HPE Smart Rate port (RJ-45, maximum negotiated speed 5Gbps)
- Auto-sensing link speed (100/1000/2500/5000BASE-T) and MDI/MDX
- 802.3az Energy Efficient Ethernet (EEE)
- PoE-PD: 48 Vdc (nominal) 802.3at PoE
• One 10/100/1000BASE-T Ethernet network interface (RJ-45)
- Auto-sensing link speed and MDI/MDX
- 802.3az Energy Efficient Ethernet (EEE)
- PoE-PD: 48 Vdc (nominal) 802.3at PoE
• Link aggregation (LACP) support between both network ports for redundancy and increased capacity
• DC power interface, accepts 1.35/3.5-mm center-positive circular plug with 9.5-mm length
• USB 2.0 host interface (Type A connector)
• Bluetooth Low Energy (BLE) radio
- Up to 4 dBm transmit power (class 2) and -91 dBm receive sensitivity
- Integrated antenna with roughly 30 degrees downtilt and peak gain of 5.1 dBi (AP-334/IAP-334) or 2.2 dBi (AP-335/IAP-335)
• Visual indicators (tri-color LEDs): for System and Radio status
• Reset button: factory reset (during device power up)
• Serial console interface (RJ-45, RS232)
• Kensington security slot
POWER SOURCES AND CONSUMPTION
• The AP supports direct DC power and Power over Ethernet (PoE)
• When both power sources are available, DC power takes priority over PoE
• Power sources are sold separately
• Direct DC source: 48Vdc nominal, +/- 5%
- Interface accepts 1.35/3.5-mm center-positive circular plug with 9.5-mm length
• Power over Ethernet (PoE): 48 Vdc (nominal) 802.3af/802.3at compliant source
- When using IPM, the AP may enter power-save mode with reduced functionality when powered by a PoE source (see details on Intelligent Power Monitoring in this datasheet)
- Without IPM the AP will apply some fixed restrictions when using PoE:
- The USB interface is disabled when using an 802.3at PoE power source
- The USB interface and second Ethernet port are disabled, and both radios operate in 1x1 mode when using an 802.3af POE power source
• Maximum (worst-case) power consumption: 25.3W (802.3at PoE), 13.2W (802.3af PoE) or 25W (DC)
- Excludes power consumed by external USB device (and internal overhead); this could add up to 5.9W (PoE or DC) for a 5W/1A USB device
• Maximum (worst-case) power consumption in idle mode: 10.9W (PoE or DC)
MOUNTING
• The AP ships with two (white) mounting clips to attach to a 9/16-inch or 15/16-inch flat T-bar drop-tile ceiling.
• Several optional mount kits are available to attach the AP to a variety of surfaces; see the Ordering Information section below for details
MECHANICAL
• Dimensions/weight (unit, excluding mount accessories):
- - 225mm (W) x 224mm (D) x 52mm (H) 8.9” (W) x 8.9” (D) x 2.0” (H)
- 1150g/41oz
• Dimensions/weight (shipping):
- 335mm (W) x 290mm (D) x 76mm (H) 13.2” (W) x 11.4” (D) x
Виж още Аксеспойнт/Репитер Безжични HPE
Виж всички Аксеспойнт/Репитер Безжични в категорията
(JW823A)
WI-FI RADIO SPECIFICATIONS
• AP type: Indoor, dual radio, 5 GHz 802.11ac 4x4 MIMO and 2.4 GHz 802.11n 4x4 MIMO
- In addition to 802.11n, the 2.4 GHz radio supports all 802.11ac features as well (proprietary extension)
• Software-configurable dual radio supports 5 GHz (Radio 0) and 2.4 GHz (Radio 1)
• 5 GHz:
- Four spatial stream Single User (SU) MIMO for up to 1,733 Mbps wireless data rate to individual 4x4 VHT80 or 2x2 VHT160 client devices
- Four spatial stream Multi User (MU) MIMO for up to 1,733 Mbps wireless data rate to up to three MU-MIMO capable client devices simultaneously
• 2.4 GHz: Four spatial stream Single User (SU) MIMO for up to 800 Mbps wireless data rate to individual 4x4 VHT40 client devices (600 Mbps for HT40 802.11n client devices)
• Support for up to 255 associated client devices per radio, and up to 16 BSSIDs per radio
• Supported frequency bands (country-specific restrictions apply):
- 2.400 to 2.4835 GHz
- 5.150 to 5.250 GHz
- 5.250 to 5.350 GHz
- 5.470 to 5.725 GHz
- 5.725 to 5.850 GHz
• Available channels: Dependent on configured regulatory domain
• Dynamic frequency selection (DFS) optimizes the use of available RF spectrum
• Supported radio technologies:
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
• Supported modulation types:
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
• Transmit power: Configurable in increments of 0.5 dBm
• Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):
- 2.4 GHz band: +24 dBm (18 dBm per chain)
- 5 GHz band: +24 dBm (18 dBm per chain)
- Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain
• Advanced Cellular Coexistence (ACC) minimizes interference from cellular networks
• Maximum ratio combining (MRC) for improved receiver performance
• Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
• Short guard interval for 20 MHz, 40 MHz, 80 MHz and 160 MHz channels
• Space-time block coding (STBC) for increased range and improved reception
• Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
• Transmit beam-forming (TxBF) for increased signal reliability and range
• Supported data rates (Mbps):
- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 600 (MCS0 to MCS31)
- 802.11ac: 6.5 to 1,733 (MCS0 to MCS9, NSS = 1 to 4 for VHT20/40/80, NSS = 1 to 2 for VHT160)
• 802.11n high-throughput (HT) support: HT 20/40
• 802.11ac very high throughput (VHT) support: VHT 20/40/80/160
• 802.11n/ac packet aggregation: A-MPDU, A-MSDU
WI-FI ANTENNAS
• AP-334/IAP-334: Four RP-SMA connectors for external dual band antennas. Internal loss between radio interface and external antenna connectors (due to diplexing circuitry): 2.3 dB in 2.4 GHz and 1.2 dB in 5 GHz.
• AP-335/IAP-335
- Four (vertically polarized) integrated 2.4 GHz downtilt omni-directional antennas for 4x4 MIMO with peak antenna gain of 4.3 dBi per antenna.
- Each 5 GHz radio chain has both a vertically and a horizontally polarized antenna element; AP software automatically and dynamically selects the best set of elements for each data packet transmitted or received.
- Four integrated vertically polarized 5 GHz downtilt omnidirectional antennas for 4x4 MIMO with peak antenna gain of 5.4 dBi per antenna
- Four integrated horizontally polarized 5 GHz downtilt omni-directional antennas for 4x4 MIMO with peak antenna gain of 4.2 dBi per antenna
- Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 degrees.
- Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the effective per-antenna pattern is 2.6dBi in 2.4 GHz and 2.5 dBi (vertical) or 2.1 dB (horizontal) in 5 GHz.
OTHER INTERFACES
• One HPE Smart Rate port (RJ-45, maximum negotiated speed 5Gbps)
- Auto-sensing link speed (100/1000/2500/5000BASE-T) and MDI/MDX
- 802.3az Energy Efficient Ethernet (EEE)
- PoE-PD: 48 Vdc (nominal) 802.3at PoE
• One 10/100/1000BASE-T Ethernet network interface (RJ-45)
- Auto-sensing link speed and MDI/MDX
- 802.3az Energy Efficient Ethernet (EEE)
- PoE-PD: 48 Vdc (nominal) 802.3at PoE
• Link aggregation (LACP) support between both network ports for redundancy and increased capacity
• DC power interface, accepts 1.35/3.5-mm center-positive circular plug with 9.5-mm length
• USB 2.0 host interface (Type A connector)
• Bluetooth Low Energy (BLE) radio
- Up to 4 dBm transmit power (class 2) and -91 dBm receive sensitivity
- Integrated antenna with roughly 30 degrees downtilt and peak gain of 5.1 dBi (AP-334/IAP-334) or 2.2 dBi (AP-335/IAP-335)
• Visual indicators (tri-color LEDs): for System and Radio status
• Reset button: factory reset (during device power up)
• Serial console interface (RJ-45, RS232)
• Kensington security slot
POWER SOURCES AND CONSUMPTION
• The AP supports direct DC power and Power over Ethernet (PoE)
• When both power sources are available, DC power takes priority over PoE
• Power sources are sold separately
• Direct DC source: 48Vdc nominal, +/- 5%
- Interface accepts 1.35/3.5-mm center-positive circular plug with 9.5-mm length
• Power over Ethernet (PoE): 48 Vdc (nominal) 802.3af/802.3at compliant source
- When using IPM, the AP may enter power-save mode with reduced functionality when powered by a PoE source (see details on Intelligent Power Monitoring in this datasheet)
- Without IPM the AP will apply some fixed restrictions when using PoE:
- The USB interface is disabled when using an 802.3at PoE power source
- The USB interface and second Ethernet port are disabled, and both radios operate in 1x1 mode when using an 802.3af POE power source
• Maximum (worst-case) power consumption: 25.3W (802.3at PoE), 13.2W (802.3af PoE) or 25W (DC)
- Excludes power consumed by external USB device (and internal overhead); this could add up to 5.9W (PoE or DC) for a 5W/1A USB device
• Maximum (worst-case) power consumption in idle mode: 10.9W (PoE or DC)
MOUNTING
• The AP ships with two (white) mounting clips to attach to a 9/16-inch or 15/16-inch flat T-bar drop-tile ceiling.
• Several optional mount kits are available to attach the AP to a variety of surfaces; see the Ordering Information section below for details
MECHANICAL
• Dimensions/weight (unit, excluding mount accessories):
- - 225mm (W) x 224mm (D) x 52mm (H) 8.9” (W) x 8.9” (D) x 2.0” (H)
- 1150g/41oz
• Dimensions/weight (shipping):
- 335mm (W) x 290mm (D) x 76mm (H) 13.2” (W) x 11.4” (D) x
Виж още Аксеспойнт/Репитер Безжични HPE
Виж всички Аксеспойнт/Репитер Безжични в категорията
Документация
Технически характеристики
Тип: | Аксес пойнт |
---|---|
Монтаж: | За вътрешен монтаж |
Безжична скорост: | 1700 Mbps |
Wi-Fi Стандарт: | Wi-Fi 5 (802.11ac) |
Честота: | 2.4 & 5 GHz |
Антени: | 4 Вътрешни |
dBi на антена/и: | Не е указано |
PoE: | In |
Интерфейс: | 1x 1000 |
Други: | Няма |
Добави Ревю / Въпрос
Оцени продукта или задай въпрос?
- 5
- 4
- 3
- 2
- 1
-
Какво пазаруват другите
-
Най-продавани продукти
-
Промоционални продукти
-
40.68 лв
-
1200.42 лв
-
93.25 лв
-
93.25 лв
-
93.25 лв
-
135.46 лв
-
122.80 лв
-
244.57 лв
-
175.05 лв
-
42.13 лв
-
111.96 лв
-
122.61 лв
-
31.93 лв
-
70.99 лв
-
215.69 лв
-
205.66 лв
-
175.05 лв
-
154.99 лв
-
130.37 лв
-
389.65 лв
-
254.92 лв
-
79.99 лв
-
18.81 лв
-
25.33 лв
-
45.31 лв
-
259.99 лв
-
188.61 лв
-
132.40 лв
143.87 лв -
70.99 лв
-
106.98 лв
-
132.40 лв
143.87 лв -
132.40 лв
143.87 лв -
132.40 лв
143.87 лв -
179.36 лв
-
14.54 лв
-
79.99 лв
-
122.61 лв
-
42.64 лв
-
161.99 лв
-
713.27 лв
-
84.99 лв
-
70.99 лв
-
44.77 лв
-
79.99 лв
-
205.66 лв
-
24.99 лв
-
88.98 лв
-
25.28 лв
-
9.13 лв
-
86.03 лв
-
84.98 лв
-
52.99 лв
-
48.99 лв
-
154.99 лв
-
161.99 лв
-
42.64 лв
-
44.99 лв
-
99.99 лв
-
93.25 лв
-
175.76 лв
-
51.62 лв
-
68.99 лв
-
47.99 лв
-
466.23 лв
-
259.99 лв
-
119.99 лв
-
18.14 лв
-
406.99 лв
-
214.99 лв
-
154.99 лв
-
189.98 лв
-
80.01 лв
-
222.99 лв
-
254.92 лв
-
35.40 лв
-
79.99 лв
-
164.99 лв
-
154.02 лв
-
294.88 лв
-
326.30 лв
-
1097.02 лв
1132.79 лв -
14.08 лв
14.64 лв -
462.32 лв
485.76 лв -
969.88 лв
994.64 лв -
15.96 лв
17.98 лв -
288.76 лв
305.90 лв -
95.90 лв
104.99 лв -
192.23 лв
199.84 лв -
3205.18 лв
3295.08 лв -
85.70 лв
93.60 лв -
344.52 лв
364.86 лв -
154.84 лв
164.21 лв -
128.51 лв
139.65 лв -
252.44 лв
270.97 лв -
496.80 лв
510.60 лв -
196.90 лв
208.32 лв -
185.50 лв
211.22 лв -
2279.84 лв
2343.17 лв -
231.33 лв
240.49 лв -
671.65 лв
779.76 лв -
162.70 лв
172.10 лв -
27.23 лв
28.99 лв -
119.70 лв
126.54 лв -
13.31 лв
15.99 лв -
48.30 лв
86.36 лв -
29.50 лв
32.49 лв -
440.65 лв
456.52 лв -
931.50 лв
1231.70 лв -
283.30 лв
291.98 лв -
68.57 лв
71.29 лв -
188.61 лв
205.32 лв -
216.01 лв
225.72 лв -
1944.64 лв
1998.74 лв -
185.81 лв
196.10 лв -
149.30 лв
214.80 лв -
1521.46 лв
1779.13 лв -
102.93 лв
106.46 лв -
325.31 лв
364.16 лв -
33.73 лв
34.99 лв -
132.40 лв
143.87 лв




Свързани продукти и тагове:
Свързани продукти
Точка за достъп Mimosa А6, 5-6GHz, 8x8 MU-MIMO, 24 dBm, 1x 10GbE, 7 Gbps, PTMP
4124.95лв
Точка за достъп Cisco Catalyst 9130AX, 2.4/5 GHz, Wi-Fi AX, 1 x 1/2.5/5GBase-T (UPOE), 1 вътрешна антена
3611.92лв
Точка за достъп Ubiquiti UAP-AC-HD-5, комплект от 5бр., 2.4GHz(800Mbps)/5GHz(1733Mbps), 2x LAN1000, PoE, 4x(2x3dBi & 2x 4dBi) вътрешни антени
3205.18лв