Точка за достъп HPE Aruba Instant 215, 2.4GHz(450Mbps)/5GHz(1.3Gbps), 1x LAN1000, USB 2.0 Type A, 6x вътрешни антени

HPE Aruba Instant 215
JL186A
Affordable, high-performance 802.11ac


Multifunctional and affordable Aruba Instant 215 wireless access points (APs) maximize mobile device performance in medium-density, high-performance Wi-Fi environments.


UNIQUE BENEFITS

• Wi-Fi client optimization
-IAP-215 features patented ClientMatch™ technology to eliminate sticky client behavior while users roam. ClientMatch continuously gathers session performance metrics from mobile devices.
-If a mobile device moves away from an AP or if RF interference impedes performance, ClientMatch automatically steers the device to a better AP.

• Advanced Cellular Coexistence (ACC)-ACC lets WLANs to perform at peak efficiency by minimizing interference from 3G/4G LTE networks, distributed antenna systems and commercial small cell/femtocell equipment.

• Quality of service for unified communication apps-IAP-215 supports priority handling and policy enforcement for unified communication apps, including Microsoft Lync with encrypted videoconferencing, voice, chat and desktop sharing.

• A single AP automatically distributes the network configuration to other Instant APs in the WLAN. Simply power-up one Instant AP, configure it over the air, and plug in the other APs – the entire process takes about five minutes.


TECHNICAL SPECIFICATIONS
2.4-GHz (450 Mbps max rate) and 5-GHz (1.3 Gbps max rate) radios, each with 3x3 MIMO and six integrated omni-directional downtilt antennas.

OPERATING MODES
• Aruba Instant AP
• Air monitor (AM) for wireless IDS, rogue detection and containment
• Spectrum analyzer, dedicated or hybrid
• Secure enterprise mesh

WIRELESS RADIO SPECIFICATIONS
• AP type: Indoor, dual radio, 5 GHz 802.11ac and 2.4 GHz 802.11n 3x3:3
• Software-configurable dual radio supports 5 GHz (Radio 0) and 2.4 GHz (Radio 1)
• 3x3 MIMO with three spatial streams and up to 1.3 Gbps wireless data rate
• Support for up to 255 associated client devices per radio, and up to 16 BSSIDs per radio
• Supported frequency bands (country-specific restrictions apply):
-2.4000 GHz to 2.4835 GHz
-5.150 GHz to 5.250 GHz
-5.250 GHz to 5.350GHz
-5.470 GHz to 5.725GHz
-5.725 GHz to 5.850GHz
• Available channels: Dependent on configured regulatory domain
• Dynamic frequency selection (DFS) optimizes the use of available RF spectrum
• Supported radio technologies:
-802.11b: Direct-sequence spread-spectrum (DSSS)
-802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
• Supported modulation types:
-802.11b: BPSK, QPSK, CCK-802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
• Transmit power: Configurable in increments of 0.5 dBm
• Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):
-2.4-GHz band: +23 dBm (18 dBm per chain)
-5-GHz band: +23 dBm (18 dBm per chain)
• Advanced Cellular Coexistence (ACC) minimizes interference from cellular networks
• Maximum ratio combining (MRC) for improved receiver performance
• Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
• Short guard interval for 20-MHz, 40-MHz and 80-MHz channels
• Space-time block coding (STBC) for increased range and improved reception
• Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
• Transmit beamforming (TxBF) for increased signal reliability and range
• Supported data rates (Mbps):
-802.11b: 1, 2, 5.5, 11
-802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
-802.11n: 6.5 to 450 (MCS0 to MCS23)
-802.11ac: 6.5 to 1,300 (MCS0 to MCS9, NSS = 1 to 3)
• 802.11n high-throughput (HT) support: HT 20/40
• 802.11ac very high throughput (VHT) support: VHT 20/40/80
• 802.11n/ac packet aggregation: A-MPDU, A-MSDU

ANTENNAS
Six integrated downtilt omni-directional antennas for 3x3 MIMO with maximum antenna gain of 5.0 dBi in 2.4 GHz and 5.0 dBi in 5 GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 degrees.

OTHER INTERFACES
• One 10/100/1000BASE-T Ethernet network interface (RJ-45)
-Auto-sensing link speed and MDI/MDX-802.3az Energy Efficient Ethernet (EEE)
-PoE-PD: 48 Vdc (nominal) 802.3af or 802.3at PoE
• DC power interface, accepts 1.7/4.0-mm center-positive circular plug with 9.5-mm length
• USB 2.0 host interface (Type A connector)
• Visual indicators (LEDs):
-Power/system status
-Ethernet link status (ENET)
-Radio status (two; RAD0, RAD1)
• Reset button: factory reset (during device power-up)
• Serial console interface (RJ-45)
• Kensington security slot

POWER
• Maximum (worst-case) power consumption: 14.9 watts (PoE) or 13.6 watts (DC)
-Excludes power consumed by external USB device (and internal overhead); this could add up to 6 watts (PoE) or 5.5 watts (DC) for 5W/1A USB device
• Maximum (worst-case) power consumption in idle mode: 8.2 watts (PoE) or 7.4 watts (DC)
• Direct DC source: 12 Vdc nominal, +/- 5%
• Power over Ethernet: 48 Vdc (nominal) 802.3af/802.3at compliant source
-USB port is disabled when using an 802.3af PoE power source; for unrestricted operation with PoE power, use an 802.3at compliant source
• Power sources sold separately
• When both power sources are available, DC power takes priority

MTBF: 538,975 hours (61.5 years) at +25° C operating temperature

180 mm x 180 mm x 45 mm (W x D x H)
610 g



Виж още Аксеспойнт/Репитер Безжични HPE
Виж всички Аксеспойнт/Репитер Безжични в категорията